• Welcome to OGBoards 10.0, keep in mind that we will be making LOTS of changes to smooth out the experience here and make it as close as possible functionally to the old software, but feel free to drop suggestions or requests in the Tech Support subforum!

Official Pit Home Improvement/DIY thread

I'm quickly developing a love affair with Bosch branded tools. I have quite a few on my Xmas list this year.
 
TWDeac, what's causing the love affair? Warranty, lifetime battery replacement? Something else?
 
I'm quickly developing a love affair with Bosch branded tools. I have quite a few on my Xmas list this year.
I've always liked the Bosch tools I've owned and used. Its one of the brands I always look for as long as its not crazy expensive. Last year, Lowes put a decent amount of Bosch and Dewalt stuff on sale for Black Friday.
 
I'm trying to determine the biggest size TV I can get that will fit into my niche above the fireplace. Right now I have a 42-inch and I think I might actually be able to fit a 47-inch TV in there. Does anyone know of some type of website or modeling program where I could enter the size, height, etc of my niche and it could calculate the max size TV I can get? It's a little tricky since the niche is curved at the top, the highest point is about 30 inches, and it's about 46 inches wide.
 
Just use a tape measure vertical and one horizontal to make half a box. Compare with dimensions listed on spec sheet for TV you're interested in.
 
There are multiple web sites that list the actual width/height/depth of TV's. Also whether they require any clearance on the sides, back and/or top/bottom for air movement (cooling). May not be much, perhaps an inch or half inch each side. The arch in your niche may be sufficient for this. You may find that the one size TV in one brand will fit, while the same size ( screen diagonal) in another may not.
 
I hope he posts about the process/how long all the steps took in this thread too.
 
Based on TWDeac's post about Bosch tools, does anybody have any experience with Ridgid tools? Most notably their lithium ion line of drills and impact divers and such? I've read some good reviews and i like the lifetime warranty on batteries. Those suckers are expensive.
 
So, Mrs. LK had been hounding me for a new dining room table for the last few months. Our toddler has outgrown his high chair, and our old table was a 4 person, tall bar-style table. Really nice table, but not practical for family dining anymore.

Then she dropped the bombshell on me that she wanted me to build the table myself using the following plans:
Triple Pedastal Farmhouse Table
Triple Pedastal Farmhouse Bench

I modified the plans a bit to take advantage of some of the woodworking skills I have vs the simple DIY methods shown in the plans.

The goal was to have the table appear somewhat rustic, so perfection was not a necessity, which was nice given I was working with fairly average wood.

What follows are a series of photos I took during construction, with some comments added. Some of the photos came out really grainy...sorry.

Here is the before photo of the pile of lumber. All told, I spent about $200 on the wood. It took me hours to find enough wood that was perfectly straight. I had zero desire to have to pull out the planer or the jointer to mill the lumber down to perfection. Again, it's supposed to be rustic. What you see is mostly prime stud lumber and the 1x6 boards are the higher grade pine boards you can buy at Lowe's.
1402207_10202592542072961_90751559_o.jpg



Here is the assembled pedestal for the table. I put it together in the hallway in my house because it was a 100% flat area. Our garage (which was converted to my workshop for the last 2 weeks) has a few degrees of slope to the floor which would have made assembling this and getting it perfectly square a nightmare. My #1 goal was for the base to be absolutely perfect with respect to how it sits on the floor and the supports all being level and aligned properly.
1455109_10202592541472946_669876143_n.jpg




The table top itself was composed of two huge panels, which I made using the 1x6 pine boards. They were all edge joined using dowel pins(self aligning dowel jig FTW) and wood glue. I clamped them overnight to allow the glue to set. The arches on the base were made using a jigsaw. The below pics are the raw table top sitting on top of the pedestal:
1471117_10202592539272891_122607867_n.jpg

1479263_10202592538512872_1264483987_n.jpg



The next step was to add the apron, which was done with 1x3 pine boards, finishing nails and more wood glue. Again it was all clamped overnight to dry.
1465863_10202592533472746_169800946_o.jpg

1385368_10202592532072711_873406678_n.jpg



Next step was the bench. The bench was made from 2x4 stud lumber. It's joined together with dowel pins and wood glue. These pics show the bench clamped and drying.
1415040_10202592531552698_1519062703_o.jpg

1102720_10202592530232665_1258137877_o.jpg



The next couple days were spent sanding the hell out of this thing. I started with 100 grit and worked my way through 200 and then 400 grit using an orbital sander. The final sanding was done by hand with the 400 grit. In this pic you can see the sanded table top. You'll also notice a slight gap in the wood in the bottom right where the panel didn't sit flush with the frame. My wife wanted me to leave it alone to keep the rustic feel, so I did. Personally, I wanted to pull the frame off and redo the whole thing.
1410825_10202592529232640_52874620_o.jpg



Finally, time to do some staining. The table top after 2 coats of Rustoleum wood stain (the color was "Carrington"):
1402874_10202592518072361_1735031463_o.jpg

1476682_10202592524872531_2104736921_n.jpg


Time to stain the rest of the pieces...my garage was stretched to the limits for this...
1399842_10202592514512272_1188759448_o.jpg

1450223_10202592510512172_746194947_n.jpg



Polyurethane time. We used Rustoleum semi-gloss. 4 thin coats, with sanding using 600 grit paper between coats. After sanding, wipe clean with a tack cloth and re-apply the polyurethane.
1415083_10202592505712052_1278351301_o.jpg

1398616_10202592507752103_1697999778_o.jpg

921283_10202592505352043_2019417424_o.jpg



And finally, the assembled table and bench in our dining space:
1397531_10202592504912032_1939913650_o.jpg

1404917_10202592504792029_356949713_o.jpg

1398148_10202592503952008_86805639_o.jpg



The finished table is 93" x 40" and weighs a freaking ton.
 
I have to run off for a meeting. I'll answer any questions when I get back.
 
That is impressive.

Did you consider doing a second bench (to have one on each side of the table)?
 
Back
Top