lbE08
Stegosaurus are bush league
- Joined
- Mar 16, 2011
- Messages
- 28,924
- Reaction score
- 2,724
but LVP I think has a more universal appeal given the durability/cost.
...does it? Honest question.
but LVP I think has a more universal appeal given the durability/cost.
Yeahhhh at least in our market even if you go high-end I still think buyers think less of it/it hurts your resell value vs even the more affordable hardwoods. Unless it's something like a basement or elsewhere that you'd really want more waterproof flooring (and finished concrete seems to be the most popular choice in basements here for that)....does it? Honest question.
This was my thinking. Especially on a main floor, hardwoods are preferred. Laminate in the basement makes sense, though.Yeahhhh at least in our market even if you go high-end I still think buyers think less of it/it hurts your resell value vs even the more affordable hardwoods. Unless it's something like a basement or elsewhere that you'd really want more waterproof flooring (and finished concrete seems to be the most popular choice in basements here for that).
...does it? Honest question.
For kids and pets LVP is a really good alternative to wall-to-wall carpet. It makes cleanup a lot easier. However, you may need to treat it as semi-disposable flooring. That is, use it for a while, then put in something else when you are preparing to move.Universal isn’t the right word. I think for people with pets/kids LVP is a more attractive option if you’re putting them in your house.
If you’re looking at houses the preference is hardwood.
Are you certain that the branch didn't damage the wood roof deck underneath the shingles?this may have been asked and answered but here goes.
We have a stick built shed thats pretty nice. We use it for storage and a workout area for our son. A branch, during a winter storm, punctured a small hole. I watched a few videos on replacing the shingles and it looks reasonable, plus I have leftover shingles from when we built it. Anyone do this? Moderately easy with a flat crow bar and some roofing nails?
I am certain it actually did. The particle board sheathing has a small hole where I can see some daylight through.Are you certain that the branch didn't damage the wood roof deck underneath the shingles?
Change the batteries in the remote.
Are there cracks in the particle board surrounding the hole? If so, you may want to put a cross brace between the two roof rafters on each side of the hole so the hole is covered from inside view. I would use a piece of 2x6 or 2x8 cut to fit between the rafters. Put it tight against the roof decking. Attach to rafters on each side.I am certain it actually did. The particle board sheathing has a small hole where I can see some daylight through.
Ceiling fan issues:
It's on a single, non-dimming switch with a remote that controls the fan speed and lights
The lights blink on and off - often not coming on at all
What I've tried:
- Uninstalling and reinstalling to check that the wiring at the point of installation is secure
- Using different bulbs (Using LED bulbs, tried low watt incandescent and had a similar effect, put back the LEDs)
- Replaced the wall switch
- Looked in the housing for a wattage limiter, but couldn't locate one (It has a circuit board b/c of the remote instead of just wiring - not sure if a limiter is part of the CB, but couldn't find a stand alone one)
Any ideas?
How hard is it to install a ceiling fan? There are 3 or 4 spots in the new house that already have a ceiling plate where one used to be, and I'm just thinking that I might want to put a couple up. Don't really want to pay a handyman to do it, but also not sure if I'm up to the task.
Its about the size of a golf ball. The particle board is a bit splintered and I thought about doing exactly what you suggested. Appreciate the assist.Are there cracks in the particle board surrounding the hole? If so, you may want to put a cross brace between the two roof rafters on each side of the hole so the hole is covered from inside view. I would use a piece of 2x6 or 2x8 cut to fit between the rafters. Put it tight against the roof decking. Attach to rafters on each side.
Im guessing that the hole is probably as big as your hand, or close. You also might want to put a piece of particle board in it so there isn't a big space for shingles to sag in the sun. Either cut a custom shape of particle board or square off the hole after you remove the shingles. And then cut a plug to fit. Screw it to the cross brace mentioned above. Then redo the felt paper and shingles.
That must have been a perfectly aimed branch to make that small a hole yet penetrate shingles and particle board.Its about the size of a golf ball. The particle board is a bit splintered and I thought about doing exactly what you suggested. Appreciate the assist.
Caveat: I'm the guy asking for help about fans, but I've installed 4 others in our house with no problems.How hard is it to install a ceiling fan? There are 3 or 4 spots in the new house that already have a ceiling plate where one used to be, and I'm just thinking that I might want to put a couple up. Don't really want to pay a handyman to do it, but also not sure if I'm up to the task.
How hard is it to install a ceiling fan? There are 3 or 4 spots in the new house that already have a ceiling plate where one used to be, and I'm just thinking that I might want to put a couple up. Don't really want to pay a handyman to do it, but also not sure if I'm up to the task.
not hard at all. You'll probably need an extra set of hands, though, to hold the unit while you're connecting wires.
There is a difference between installing a fan, which usually means screwing in a bunch of screws and connecting three wires and trouble shooting intermittent faults in electronic components.Caveat: I'm the guy asking for help about fans, but I've installed 4 others in our house with no problems.
It's really easy as long as you have an existing fixture. An extra set of hands is nice, but a lot of fans have a hook that will hold the fan in place while you connect the wiring.